Sorensen SGA60-167
DC Power Supply, 60V, 167A, 10kW

Download Product Datasheet

Product Overview

RENT SORENSEN SGA60-167 DC POWER SUPPLY (Call for Availability)

The Sorensen SGA60-167 DC Power Supply (SGA = Sorensen General Purpose Analog), is a high powered, programmable power supply designed for exceptional load transient response, low noise, and the high power density. The power density is enhanced by a stylish front air intake allowing supplies to be stacked without any required clearance between units. The Sorensen SGA60-167 with its high performance power electronics, meets the need for simple front panel analog controls or external control.

Features and Specifications of the Sorensen  SGA60-167 DC Power Supply include:

Features:

• 10-turn potentiometers for setting voltage and current
• 3 ½ digit LED readout
• Front panel over-voltage protection (OVP) preview/adjustment and reset
• High power density 10 kW in a 3U chassis
• Current: 167A
• Wide voltage range: up to 60V
• Fast load transient response means protection from undesired voltage excursions
• Low ripple and noise
• Hardware trigger (Ethernet option)
• Parallelable up to 150 kW make it expandable as requirements grow
• Sequencing: free system controller and speed up test
• Low audible noise with temperature controlled variable speed fans

Specifications:

• Common:
• Remote Sense:
• Terminals are provided to sense output voltage at point of load
• Maximum line drop 5% of rated voltage per line for 40-100V models
• Greater line drop is allowed, but output regulation specifications no longer apply
• Parallel Operation:
• Up to 5 units may be paralleled for additional current within the power supply single-unit specifications, with exception of the DC output current set accuracy
• Additional paralleled SG units will add 0.3% inaccuracy per unit
• Series Operation:  Up to 2 units
• Input:
• Nominal Voltage 3 phase, 3 wire + ground:
• 208/220 VAC (operating range 187 - 242 VAC)
• 380/400 VAC (operating range 342 - 440 VAC)
• 440/480 VAC (operating range 396 - 528 VAC)
• Frequency:  47 - 63Hz, 400Hz
• Power factor:
• >0.9 typical for 10V - 30V, 50V, 1000V and other models with optional "PF" modification
• >0.75 typical for 208/220 VAC input (40V, 60V - 800V models, 0.9 available with modification "PF")
• >0.72 typical for 380/480 VAC input (40V, 60V - 800V models, 0.9 available with modification "PF")
• >0.69 typical for 440/480 VAC input (40V, 60V - 800V models, 0.9 available with modification "PF")
• Protection:
• ½ cycle ride through, typical, on all three phases
• 3 cycle ride through on single phase
• Missing phase shutdown (800V model 6.4 msec on all 3 phases)
• Programming & Read-back Specifications:
• Front Panel Display: 
• Programming:
• Accuracy: +/- (0.5%fs + 1 digit)
• Resolution: 3.5 digits
• Read-Back Monitoring:
• Accuracy: +/- (0.5%fs + 1 digit)
• Resolution: 3.5 digits
• Knob control & Display read-back
• Remote Analog Interface: 
• Programming:
• Accuracy:
• Voltage: +/-0.25% of full scale 
• Current: 0.8% of full scale 
• Read-Back Monitoring:
• Accuracy: +/-1.0% of full scale
• 25-pin D-sub connector (0~5 V or 0~10 V)
• Remote Digital Interface:
• Programming:
• Accuracy:
• Voltage:  +/- 0.1% of full scale
• Current: +/- 0.4% of full scale
• Resolution: +/-0.002% of full scale
• Read-Back Monitoring:
• Accuracy:
• Voltage:  +/- 0.1% of full scale
• Current:  +/- 0.4% of full scale
• Resolution:  +/-0.002% of full scale
• OVP:
• Programming:
• Accuracy: +/- 1% of full scale
• Resolution: +/-0.002% of full scale
• Programming range:
• 5-110%
• Configured from front panel
• Remote analog
• Or via optional digital inputs
• User I/O: 
• Disconnect and polarity-reversal relay control (only available with Ethernet option)
• Digital 10-pin Molex type connector
• Output:
• Ripple and noise (voltage mode, typical):
• Ripple and noise specified at full load, nominal AC input
• Noise measured with 6 ft. cable, 1μf at load
• Ripple (current mode):  <+/-0.04% of full scale rms current
• Output voltage rise time (40-1000V):  ≈< 100 ms 10-90% of full scale typical - full resistive load 
• DC current slew rate:  45A/ ms typical - resistive load 
• Line regulation (with sense wires used):
• (±10% of nominal AC input, constant load)
• Voltage mode: +/- 0.01% of full scale (40-800V) 
• Current mode: +/- 0.05% of full scale (40-800V) 
• Voltage mode and current mode: +/- 0.05% of full scale (10-30V)
• Load regulation (with sense wires used):
• (no load to full load, nominal AC input)
• Voltage mode: +/- 0.02% of full scale (40-800V) 
• Current mode: +/- 0.1% of full scale 
• Load transient response:  Recovers within 1 ms to +/-0.75% of full-scale of steadystate output for a 50% to 100% or 100% to 50% load change
• Efficiency:  87% typical at nominal line and max load
• Stability:  ±0.05% of set point after 30 minute warm-up and over 8 hours at fixed line, load and temperature, typical
• Temperature coefficient:
• 0.02%/ C of maimum output voltage rating for voltage set point, typical
• 0.03%/ C of maimum output current rating for voltage set point, typical
• Output float voltage:  Negative terminal within +/- 300 V of chassis potential

Click to see all the models in this series