Keithley 2303 High Speed DC Power Supply, 0-15V, 3A or 0-9V, 5A, 45W

The Keithley 2303 Power Supply provides voltage control and power monitoring for automated testing of portable, battery-operated devices. The Keithley 2303 delivers up to 5A to handle portable device loads easily, while 100nA resolution enables precise monitoring of sleep mode currents with 0.2% basic accuracy. Fast transient response simulates battery behavior, with output returning to within 100mV of the set voltage in 40µs or less. The ability to sink current enables the Keithley 2303 Power Supply to simulate the characteristics of a discharged, rechargeable battery for testing of battery chargers and charger-related circuitry. In addition to DC current measurements, it can measure current pulses as short as 60µs and as long as 833ms.

Features and Specifications of the Keithley 2303 Power Supply include:

DC Voltage Output

• Output Voltage : 0 to +15V DC
• Output Accuracy : ±(0.05% + 10mV)
• Programming Resolution : 5mV
• Readback Accuracy: ±(0.05% + 3mV)
• Readback Resolution : 1mV
• Output Voltage Settling Time: 5ms to within stated accuracy
• Load regulation : 0.01% + 2mV
• Line Regulation : 0.5mV
• Stability: 0.01% + 0.5mV
• Transient Response To 1000% Load Change:
  • Transient Recovery Time:
    • <40µs to within 100mV of previous level
    • <80µs to within 20mV of previous level
  • Transient Voltage Drop:
    • <100mV, typical
    • <200mV, typical
• Ripple and Noise (20Hz to 20MHz): 3mV rms/8mV p-p, typical

DC Current

• Output Current : 0–9V: 5A max >9V–15V: 3A max. (not intended to be operated in parallel)
• Source Compliance Accuracy : ±(0.16% + 5mA)
• Programmed Source Compliance Resolution : 1.25mA
• Readback Accuracy:
  • 5A range: ±(0.2% + 400µA)
  • 5mA range: ±(0.2% + 1µA)
• Readback Resolution
  • 5A range: 100µA
  • 5mA range: 0.1µA
• Current Sink Capacity : 0–5V: 2A max 5V–15V: Derate 0.1A per volt above 5V
• Load regulation : 0.01% + 1mA
• Line Regulation : 0.5mA
• Stability: 0.01% + 50µA

Digital Voltmeter Input

• Input Voltage Range: 0 to +20V DC
• Input Impedance: 1010O typical
• Maximum Voltage (either input terminal) with respect to output low: –3V, +22V
• Reading Accuracy: ±(0.05% + 3mV)
• Reading Resolution : 1mV

DC General

• Measurement Time Choices: 0.01 to 10 PLC, in 0.01PLC steps
• Average Readings: 1 to 10
• Reading Time: 31ms, typical

Pulse Current Measurement Operation

• Trigger Level: 5mA to 5A, in 5mA steps
• Trigger Delay: 0 to 100ms, in 10µs steps
• Internal Trigger Delay: 25µs
• High /Low /Average Mode:
  • Measurement Aperture Settings: 33.3µs to 833ms, in 33.3µs steps
  • Average Readings: 1 to 100
• Burst Mode:
  • Measurement Aperture: 33.3µs
  • Conversion Rate: 3600/second, typical
  • Number of Samples: 1 to 5000
  • Transfer Samples Across IEEE Bus in Binary Mode: 4800 bytes/second, typical
• Long Integration Mode:
  • Measurement Time: 850ms (840ms) to 60 seconds in 16.7ms (20ms) steps